Two refrigerant changes landed in 2026, and both show up in your books as much as on the truck. One added leak-repair work on larger systems. The other changed what you can do with older R-410A equipment still on your shelf.
This post covers what changed, then the bookkeeping side: tagging leak-repair work as its own job type, splitting refrigerant from parts and labor, counting cylinders as inventory, and handling leftover equipment without distorting your margins.
One note before we start: the EPA rules tell you what has to happen in the field. They do not say how to record any of it in your books. The bookkeeping steps below are good practice, not regulation. Confirm the valuation choices with your CPA, and confirm the regulatory details for any specific system against EPA's own materials.
Leak repair on larger systems (January 1, 2026). EPA's leak repair requirements now apply to appliances with 15 pounds or more of refrigerant containing an HFC or certain HFC substitutes. Important for most HVAC shops: EPA's fact sheet says residential and light commercial air conditioning and heat pumps are not covered by these leak repair requirements. Chillers, certain variable refrigerant flow systems, and commercial refrigeration are a different story. If you service walk-in coolers, restaurant refrigeration, or larger commercial systems, this is new, recurring work.
R-410A installation deadline lifted for older equipment (May 2026). EPA finalized changes to its Technology Transitions rule that remove the January 1, 2026 installation deadline for residential and light commercial AC and heat pump systems using higher-GWP refrigerants like R-410A, as long as the equipment was manufactured or imported before January 1, 2025. That means eligible pre-2025 equipment on your shelf can still be installed until it runs out. (New York contractors are a notable exception under state rules.)
The long-term direction has not changed. The AIM Act still phases HFC production down over time, so refrigerant cost and compliance work are not going away.
Job-level costing. A leak-repair call needs its own revenue, cost, and margin, not a spot in general service revenue. Our Complete Guide to HVAC Bookkeeping covers the foundation.
Refrigerant as inventory. Set refrigerant up as an inventory item in your field software (ServiceTitan and Housecall Pro are the most common) and map it to a matching inventory account in Xero, so the shelf and the books agree.
A short tag list on the tablet: leak detection, leak repair labor, refrigerant charge, filter drier, fittings, recovery and evacuation. Short enough that techs use it every time.
Create a leak detection and repair job type in your field software instead of lumping this work into general service. That lets you count how many of these calls you ran and what each one earned.
Inside the job, separate finding the leak from fixing it. On a larger system, the cost of finding a leak is often different from the cost of repairing it. Require a refrigerant line that records pounds charged, so a small top-off and a full recovery and recharge never book as the same kind of call.
Keep the job open until the leak test clears and the final charge is recorded. Closing it at the first visit hides the second truck roll, which is often where margin disappears.
Once a month, run a report comparing revenue per leak-repair job against tech hours and pounds of refrigerant used.
On the job cost sheet, keep three separate lines: tech hours at your loaded labor rate, parts at cost plus markup, and refrigerant at your cost per pound. Do not roll them into one "supplies" number. Value refrigerant at what you actually paid for that cylinder.
For every completed job, compare pounds billed to pounds issued from inventory. An unexplained gap usually means a cylinder left the truck and was never logged.
Show the same split on the customer invoice, so the compliance work is visible instead of buried in a flat diagnostic fee.
Track cylinder inventory in an asset account with both quantity and cost per pound, in the same system that issues refrigerant to jobs. When a tech uses refrigerant on a job, the quantity drops and the cost moves to that job. The shelf count and the books move together.
Track each cylinder by type, because these are three different inventory items:
Use the same three item codes in the field app and in Xero, so a tech cannot issue "generic refrigerant" and erase the distinction. Reconcile cylinder counts monthly against purchases, job usage, and supplier returns. That variance is a real margin leak, and it is the one you can find without a leak detector.
With the May 2026 change, eligible R-410A equipment made before 2025 can still be installed, so it may be more sellable than it looked at the start of the year. Before you price, install, or write anything down, confirm each unit's status: check the manufacture date, and if you have any doubt, check EPA's current Technology Transitions materials.
On the bookkeeping side, keep regulation and accounting separate. Whether a unit can be installed affects whether you can sell it, not what you paid for it. If some older stock is moving slowly, ask your CPA before year-end whether a write-down makes sense and put the chosen method in writing.
Keep any write-down out of job costs. An inventory adjustment on the shelf should not change the margin on jobs you already finished, or you will misread which service lines make money.
Take a restaurant walk-in cooler with a 20-pound HFC charge, a confirmed leak, a repaired joint, and a full recharge. At 20 pounds of HFC, this is the kind of commercial refrigeration appliance the 2026 leak repair requirements cover. (A residential or light commercial AC system of the same size would not be.)
On the job cost sheet, the lines stay separate: 3.5 tech hours at your loaded rate, a filter drier and two fittings at cost plus markup, 20 pounds issued from purchased cylinder stock at your cost per pound, and recovery and evacuation time on its own line.
Inventory moves both ways against the same job number: 20 pounds out of purchased stock, and any refrigerant recovered from the old charge logged back in as recovered stock.
The split answers the question that matters: margin before and after refrigerant cost, and whether the flat fee you charge for this kind of call ever covered the work. Posted as a supply purchase, the job would have hidden all of that.
Start with two things: add the leak-repair job type with a separate refrigerant line, and reconcile cylinder inventory by hand for one month to see how big the gap is. Have your CPA review how refrigerant and cylinders are set up in your chart of accounts, and write down the agreed method so the field and the office follow one rule.
If your field app and Xero are not talking to each other cleanly, fix that first. Job costing is only as trustworthy as that connection.
The 2026 rules changed what you have to do on the truck. Your books decide whether any of it shows up as profit.
Want to know whether your job costing is ready for this kind of work? Take the free 3-Minute Financial Triage.
Take the free 3-minute Financial Triage and find out exactly where your business stands.
Ready to talk now? Book a free 30-minute call